[Home ] [Archive]    
:: Main :: About :: Current Issue :: Archive :: Search :: Submit :: Contact ::
:: Volume 30, Issue 4 (Winter 2013) ::
J Dent Sch GYEAR__, 30(4): 233-239 Back to browse issues page
Effect of Framework Material on Stress Distribution around Implants using Three-Dimensional Finite Element Analysis
Mahroo Vojdani Dr.1, Abbas Sabouri Dr.2, Karim Jafari Corresponding Author: Dr. * 3, Salar Khajehpour 4, Ehsan Farjood Dr.2
1- Biomaterial Research Center
2- Dept. of Prosthodontics
3- Dept. of Prosthodontics , jafarik@sums.ac.ir
4- Shiraz Islamic Azad University, Shiraz-Iran
Abstract:   (6419 Views)

Objectives: Despite the high success rate, implant-supported prostheses fail in some cases. Control of the applied forces is an important factor determining the success or failure of implants. Complete understanding of the biomechanical principles in implant-supported prostheses is necessary for offering an appropriate custom-made treatment plan for each patient and reducing the risk of functional complications. Finite element analysis is a quantitative method for the assessment of force distribution in complex structures. This study sought to compare the effect of different framework materials on stress distribution in bone supporting implants using three-dimensional finite element analysis.

Methods: In this in-vitro study, a three-dimensional model of bone was obtained using Cone Beam Computerized Tomography (CBCT). Using CATIA V5R20 (Dassault Systemes, France) software, a NobelReplace tapered implant (Nobelpharma Co., Gothenburg, Sweden) measuring 13 mm in height and 4.3 mm in diameter was virtually inserted in the anterior maxilla. A titanium abutment, ZOE cement and superstructure with different frameworks (Ag-Pd, Ni-Cr, and fiber-reinforced composite) were designed. Force was applied in an amount of 178 N at three angulations of zero, 30 and 45° relative to the implant axis and the maximum von-Mises stress and maximum strain were calculated for cortical and trabecular bone.

Results: Changing the framework material caused a small change in level of stress and strain and their distribution pattern. By increasing the angulation of the applied force, amount of stress and strain in the implant-supporting bone increased. Maximum stress and strain were applied at 45° angulation. At zero degree angulation, maximum stress in the cortical bone was 17.326 MPa with Ni-Cr framework, 17.383 MPa with Ag-Pd and 17.321 MPa with fiber-reinforced composite. In loading at 30° angulation, maximum stress in the cortical bone was 136.95 MPa with Ni-Cr framework, 136.03 MPa with Ag-Pd framework and 136.18 MPa with fiber-reinforced composite framework. In loading at 45° angulation, maximum stress in the cortical bone was 161.37 MPa with Ni-Cr, 161.21 MPA with Ag-Pd and 160.4 MPawith fiber-reinforced frameworks.

Conclusion: The difference between framework materials with higher and lower strengths in amount and pattern of cortical stress and strain distribution was insignificant

Keywords: Finite element analysis, Implant, Stress, Framework, Cortical bone, Strain
Full-Text [PDF 244 kb]   (2575 Downloads)    
Type of Study: Original Article | Subject: Special
Received: 2013/02/27 | Accepted: 2018/06/3 | Published: 2018/06/3
Send email to the article author

Add your comments about this article
Your username or Email:


XML     Print

Download citation:
BibTeX | RIS | EndNote | Medlars | ProCite | Reference Manager | RefWorks
Send citation to:

Vojdani M, Sabouri A, Jafari K, Khajehpour S, Farjood E. Effect of Framework Material on Stress Distribution around Implants using Three-Dimensional Finite Element Analysis. J Dent Sch. 2013; 30 (4) :233-239
URL: http://jds.sbmu.ac.ir/article-1-1081-en.html

Volume 30, Issue 4 (Winter 2013) Back to browse issues page
مجله دانشکده دندانپزشکی دانشگاه علوم پزشکی شهید بهشتی Shahid Beheshti University Dental Journal
Persian site map - English site map - Created in 0.06 seconds with 31 queries by YEKTAWEB 3855